LuanVan.vnLuận Văn
Gửi thư

Design and implementation of statcom for reactive power compensation

Đồ án tốt nghiệp · Đại học · năm 2020 · đề tài tham khảo

Loại tài liệuĐồ án tốt nghiệp
Bậc họcĐại học
Tác giảDinh Ngoc Tien; Tran Viet Tu; Pham Tien Vu
Người hướng dẫnNguyen Le Hoa
Cơ sở đào tạoTrường Đại học Bách khoa, Đại học Đà Nẵng
Năm2020
NguồnThư viện số Trường Đại học Bách khoa, Đại học Đà Nẵng · trang gốc

Tóm tắt

Production and living electricity systems use many sensor devices such as motors, transformers, etc., which not only consume useful power (P (kW) = S * Cosφ) but also consume a large amount of useless power (Q (kVAr) = S * Sinφ), causing damage to the electrical system. Where φ (pronounced phi) is the phase angle between current and voltage. The reactive power component makes the total transmission capacity on the line increase, causing losses, overload, pressure drop, .... The greater the reactive power, the smaller Cosφ. The Electricity Industry stipulates cosφ must be at the lowest level of 0.9. If the cosine is below 0.9, the electricity user will be fined to buy reactive power. Therefore, the research on the cosφ factor compensation is necessary. The inverter circuits have many operating modes such as harmonic control, Micro Grids, Grid Storage, Active Rectifier. In this project we carry out research in VAR mode. The circuit has features: 380-DC VIN, 110 VRMS, 60 Hz, 400-VA Max Output, 20-kHz Switching, but we reduced all parameters to 10 times to be suitable for the research. The project is tested on 2 levels of testing (open loop and close current loop), the obtained resuls is generate sine wave with increasing mesh cosφ.
Bản toàn văn lưu tại thư viện Trường Đại học Bách khoa, Đại học Đà Nẵng

Thông tin và tóm tắt ở trên lấy từ kho số mở của thư viện trường. Bản toàn văn do thư viện trường quản lý — có nơi cho đọc trực tuyến, có nơi cần tài khoản bạn đọc của trường.

Mở tại thư viện trường ↗
Dùng tài liệu tham khảo cho đúng
  • Đọc để hiểu cách người trước đặt câu hỏi, chọn phương pháp, trình bày số liệu — rồi tự làm với dữ liệu và bối cảnh của bạn.
  • Ý, số liệu, bảng biểu lấy từ tài liệu này phải trích dẫn (tác giả, năm, tên đề tài, cơ sở đào tạo).
  • Đề tài trùng tên vẫn làm được nếu khác đơn vị khảo sát, thời gian hoặc cách tiếp cận — nêu rõ điểm khác trong phần mở đầu.

Đề tài cùng ngành

Tác giả muốn gỡ, sửa thông tin hoặc bổ sung bản toàn văn: gửi yêu cầu qua trang Liên hệ, kèm đường dẫn trang này.