LuanVan.vnLuận Văn
Gửi thư

Research and Design an Observation System for Water Pumping Station

Đồ án tốt nghiệp · Đại học · năm 2020 · đề tài tham khảo

Loại tài liệuĐồ án tốt nghiệp
Bậc họcĐại học
Tác giảNguyen Huu Bach; Le Duc Minh Tuan; Tran Le Quoc
Người hướng dẫnLe Quoc Huy
Cơ sở đào tạoTrường Đại học Bách khoa, Đại học Đà Nẵng
Năm2020
NguồnThư viện số Trường Đại học Bách khoa, Đại học Đà Nẵng · trang gốc

Tóm tắt

Recently the maintenance process of the water pumping station in Da Nang Software Park has several problems relating to both the delay time in management and the safety of the staff. Due to the long distance (about 70m) from the water pumping station to the office, it takes quite a lot of time to check and manage the pumps as well as collecting data process. In some specific situations, the maintenance staff might be put in danger because of some phenomenon such as water, pressure and electricity leaking. Therefore, the need for a remote monitoring device for water pumping station is very necessary. After hours of discussing, our team decide to use an application of Internet of things to execute the project because of its popularity, familiar and easy to manage. A device with the combination of microcontroller, Wifi chip ESP8266 and several sensors can make the work done properly with a sufficient amount of effort. We use the sensors and the microcontroller to measure and display the main data of the water pumping station. And then with the communication of the Wifi chip and the microcontroller, values of the station will be uploaded to the already built server of the Da Nang Software Park and be ready to monitor in the office. All the stages of the project including the sampling of the sensors are programmed and executed by Arduino IDE software (C/C++). To full fill the requirement of the project, the basic information about how the pumps operated and the daily maintenance process of the staff are firstly achieved with the help of our supervisors Mr. Nhan. At the same time, we apply the learned knowledge about schematic, printed circuit board and electrical components to do some research and carefully analyze the ways to build the product. The remote observation device for water pumping station is anticipated to operate stably in the common condition of the pump station (15 - 30 celsius degree) with the compact size (about 10cm*15cm) to install inside the technical box at the station (7-10V DC power source).
Bản toàn văn lưu tại thư viện Trường Đại học Bách khoa, Đại học Đà Nẵng

Thông tin và tóm tắt ở trên lấy từ kho số mở của thư viện trường. Bản toàn văn do thư viện trường quản lý — có nơi cho đọc trực tuyến, có nơi cần tài khoản bạn đọc của trường.

Mở tại thư viện trường ↗
Dùng tài liệu tham khảo cho đúng
  • Đọc để hiểu cách người trước đặt câu hỏi, chọn phương pháp, trình bày số liệu — rồi tự làm với dữ liệu và bối cảnh của bạn.
  • Ý, số liệu, bảng biểu lấy từ tài liệu này phải trích dẫn (tác giả, năm, tên đề tài, cơ sở đào tạo).
  • Đề tài trùng tên vẫn làm được nếu khác đơn vị khảo sát, thời gian hoặc cách tiếp cận — nêu rõ điểm khác trong phần mở đầu.

Đề tài cùng ngành

Tác giả muốn gỡ, sửa thông tin hoặc bổ sung bản toàn văn: gửi yêu cầu qua trang Liên hệ, kèm đường dẫn trang này.