NAND Flash Memory Verification Using Universal Verification Methodology
Đồ án tốt nghiệp · Đại học · năm 2018 · đề tài tham khảo
| Loại tài liệu | Đồ án tốt nghiệp |
|---|---|
| Bậc học | Đại học |
| Tác giả | Ngô Quang Hiệp; Nguyễn Kỳ Trí |
| Người hướng dẫn | Nguyễn Tấn Hưng; Hà Hữu Hiển |
| Cơ sở đào tạo | Trường Đại học Bách khoa, Đại học Đà Nẵng |
| Năm | 2018 |
| Nguồn | Thư viện số Trường Đại học Bách khoa, Đại học Đà Nẵng · trang gốc |
Tóm tắt
Recently, with the rapid growing speed of mobile devices usage in both quality as well as quantity, the requirement for memory that could be able to be stored, written, erased data with a high rate and big capacity is a critical issue that can result in the competitiveness of an electronic product. With these aims, the essential goal of this thesis is to focus on analyzing, studying as well as verifying the structure of the NAND-FLASH memory in transferring the data in term of read, write and erase functionalities by using the Universal Verification Methodology which also known as UVM standard. Within this decay, the NAND memory, an electronic (solid-state) non-volatile computer storage medium that can be electrically erased and reprogrammed, was developed by Toshiba and commonly used inside memory cards, USB flash drives etc due to its advantages in endurance within a relatively small number of write cycles in a specific block. In this thesis, we study a new product in the NAND flash memory which supports 3 different modes of interface and a larger internal data move which can read 4MB/s. To handle this project, we firstly analyzed the whole structure of the device and then started to build the environment follow the UVM flow. Up-to-date, we completed the design verification flows to test the Register Transfer Level model (RTL) for all commands that supported by this device.
Bản toàn văn lưu tại thư viện Trường Đại học Bách khoa, Đại học Đà Nẵng
Thông tin và tóm tắt ở trên lấy từ kho số mở của thư viện trường. Bản toàn văn do thư viện trường quản lý — có nơi cho đọc trực tuyến, có nơi cần tài khoản bạn đọc của trường.
Mở tại thư viện trường ↗
Dùng tài liệu tham khảo cho đúng
- Đọc để hiểu cách người trước đặt câu hỏi, chọn phương pháp, trình bày số liệu — rồi tự làm với dữ liệu và bối cảnh của bạn.
- Ý, số liệu, bảng biểu lấy từ tài liệu này phải trích dẫn (tác giả, năm, tên đề tài, cơ sở đào tạo).
- Đề tài trùng tên vẫn làm được nếu khác đơn vị khảo sát, thời gian hoặc cách tiếp cận — nêu rõ điểm khác trong phần mở đầu.
Đề tài cùng ngành
- Deploy the Voice over Internet Protocol System on Cloud
- Data Optimization and Transmission Security for E-scooter sharing system
- Thiết kế khuôn đúc cốc rót nước nhựa
- Design and implementation of SCADA for Conveyor system
- Thiết kế máy cán ren cấp phôi tự động
- Thiết kế máy ép thủy lực trong hệ thống thu gom và xử lý rác
- Register-transfer level Design with Universal Verification Methodology for Configurable Two Width Search and Write Ternary Content Addressable Memory
- Thiết kế quy trình công nghệ chế tạo chi tiết thanh giằng chống xoắn (torque link) trên cụm càng đáp mũi máy bay
Tác giả muốn gỡ, sửa thông tin hoặc bổ sung bản toàn văn: gửi yêu cầu qua trang Liên hệ, kèm đường dẫn trang này.