LuanVan.vnLuận Văn
Gửi thư

Modeling of catalytic channels and monolith reactors

Luận án · Tiến sĩ · năm 2006 · đề tài tham khảo

Loại tài liệuLuận án
Bậc họcTiến sĩ
Tác giảPeter M Struk
Cơ sở đào tạoĐại học Quốc gia TP. Hồ Chí Minh
Năm2006
NguồnThư viện số Đại học Quốc gia TP. Hồ Chí Minh · trang gốc

Tóm tắt

This dissertation presents a "lumped" two-phase (solid and gas) model of transient catalytic combustion suitable for isolated channels or monolith reactors. The gas-phase is quasi-steady relative to the transient solid. Axial diffusion is neglected; lateral diffusion, however, is accounted for using transfer coefficients. The solid phase includes axial heat conduction and external heat loss due to convection and radiation. The combustion process uses detailed gas-phase and surface reactions. The gas-phase model becomes a system of stiff ordinary differential equations while the solid-phase reduces, after discretization, into a system of stiff ordinary differential-algebraic equations. The time evolution of the system came from alternating integrations of the quasi-steady gas and transient solid. The model simulates three experiments using CO fuel: (1) steady-state conversion through an isothermal platinum tube, (2) steady-state conversion through a commercial monolith, and (3) transient propagation of a catalytic reaction inside a small platinum tube including temperature measurements. This work presents detailed parametric / sensitivity studies on important parameters in each case including internal transfer coefficients, catalytic surface site density, and external heat-loss (for the third case). For the second case, the model uses a parameter a* (ratio of apparent to geometric surface area) appropriate for enhanced surface-area washcoats in monoliths. The model requires internal mass-transfer resistance to match experiment at lower residence times. Under mass-transport limited conditions, the model reasonably predicted exit conversion using global mass-transfer coefficients. Near light-off, the model results did not match experiment precisely even after adjustment of mass-transfer coefficients. Agreement improved for the first case after adjusting the surface kinetics such that the net rate of CO adsorption increased compared to 02. The CO / 02 surface mechanism came from a sub-set of reactions in a popular CH4 / 02 mechanism. For the third case, predictions improved for lean conditions with increased external heat loss or adjustment of the kinetics as in the first case. Finally, the results show that different initial surface-species distribution (first case) as well as heating profile (second case) leads to multiple steady-states under certain conditions. These results demonstrate the utility of a lumped two-phase model of a transient catalytic combustor with detailed chemistry.
Bản toàn văn lưu tại thư viện Đại học Quốc gia TP. Hồ Chí Minh

Thông tin và tóm tắt ở trên lấy từ kho số mở của thư viện trường. Bản toàn văn do thư viện trường quản lý — có nơi cho đọc trực tuyến, có nơi cần tài khoản bạn đọc của trường.

Mở tại thư viện trường ↗
Dùng tài liệu tham khảo cho đúng
  • Đọc để hiểu cách người trước đặt câu hỏi, chọn phương pháp, trình bày số liệu — rồi tự làm với dữ liệu và bối cảnh của bạn.
  • Ý, số liệu, bảng biểu lấy từ tài liệu này phải trích dẫn (tác giả, năm, tên đề tài, cơ sở đào tạo).
  • Đề tài trùng tên vẫn làm được nếu khác đơn vị khảo sát, thời gian hoặc cách tiếp cận — nêu rõ điểm khác trong phần mở đầu.

Đề tài cùng ngành

Tác giả muốn gỡ, sửa thông tin hoặc bổ sung bản toàn văn: gửi yêu cầu qua trang Liên hệ, kèm đường dẫn trang này.