Modeling and simulation of droplet dynamics for microfluidic applications
Luận án · Tiến sĩ · năm 2019 · đề tài tham khảo
| Loại tài liệu | Luận án |
|---|---|
| Bậc học | Tiến sĩ |
| Tác giả | Hoang Van Thanh |
| Người hướng dẫn | Min Park Jang |
| Cơ sở đào tạo | Trường Đại học Bách khoa, Đại học Đà Nẵng |
| Năm | 2019 |
| Nguồn | Thư viện số Trường Đại học Bách khoa, Đại học Đà Nẵng · trang gốc |
Tóm tắt
Design of microchannel geometry plays a key role for transport and manipulation of liquid droplets and contraction microchannel has been widely used for many applications in droplet-based microfluidic systems. This study first aims to investigate droplet dynamics in contraction microchannel for more details and then to propose a simplified model used for microfluidic systems to describe droplet dynamics. In particular, for contraction microchannel, three regimes of droplet dynamics, including trap, squeeze and breakup are characterized, which depends on capillary number (Ca) and contraction ratio (C). Theoretical models have been also proposed to describe transitions from one to another regime as a function of capillary number and contraction ratio. The critical capillary number of transition from trap to squeeze has been found as a function of contraction ratio expressed as CaIc=a(CM-1), whereas critical capillary number CaIIc = c1C-1 depicts the transition from squeeze to breakup. Additionally, the deformation, retraction and breakup along downstream of the contraction microchannel have been explored for more details. To describe dynamics of droplet in microfluidic system, one-dimensional model based a Taylor analogy has been proposed to predict droplet deformation at steady state and transient behavior accurately. The characteristic time for droplet reaching steady state is dependent on viscosity ratio and the droplet deformation at steady state is significantly influenced by viscosity ratio of which the order of magnitude ranges from -1 to 1. Finally, theoretical estimation of condition for droplet breakup was also proposed in the present study, which shows a good agreement with experimental result in the literature.
Bản toàn văn lưu tại thư viện Trường Đại học Bách khoa, Đại học Đà Nẵng
Thông tin và tóm tắt ở trên lấy từ kho số mở của thư viện trường. Bản toàn văn do thư viện trường quản lý — có nơi cho đọc trực tuyến, có nơi cần tài khoản bạn đọc của trường.
Mở tại thư viện trường ↗
Dùng tài liệu tham khảo cho đúng
- Đọc để hiểu cách người trước đặt câu hỏi, chọn phương pháp, trình bày số liệu — rồi tự làm với dữ liệu và bối cảnh của bạn.
- Ý, số liệu, bảng biểu lấy từ tài liệu này phải trích dẫn (tác giả, năm, tên đề tài, cơ sở đào tạo).
- Đề tài trùng tên vẫn làm được nếu khác đơn vị khảo sát, thời gian hoặc cách tiếp cận — nêu rõ điểm khác trong phần mở đầu.
Đề tài cùng ngành
- Nghiên cứu sự khác biệt trình tự nucleotide của các vùng Gene chỉ thị ở các mẫu sen trồng tại Huế và khảo sát hoạt tính sinh học của một số hợp chất chiết tách từ hạt sen
- Nghiên cứu sơn bột
- Thiết kế phân xưởng keo phenolformaldehyde tan trong cồn với năng suất 18000 tấn/năm.
- Nghiên cứu sử dụng chai nhựa PET phế thải trong sản xuất lốp xe
- Vaporisation of Single and Binary Component Droplets in Heated Flowing Gas Stream and on Solid Sphere
- Thiết kế phân xưởng sản xuất nhựa PVC bằng phương pháp trùng hợp huyền phù năng suất 25.000 tấn/năm
- Nghiên cứu thu nhận enzyme nattokinase bằng phương pháp lên men bề mặt từ phế liệu bã đậu nành
- Thiết kế phân xưởng sản xuất nhựa Polystyren theo phương pháp trùng hợp huyền phù, năng suất 20.000 tấn/năm
Tác giả muốn gỡ, sửa thông tin hoặc bổ sung bản toàn văn: gửi yêu cầu qua trang Liên hệ, kèm đường dẫn trang này.