Maximum Power Point Tracking of a DFIG Wind Turbine System
Luận án · Tiến sĩ · năm 2017 · đề tài tham khảo
| Loại tài liệu | Luận án |
|---|---|
| Bậc học | Tiến sĩ |
| Tác giả | Phan Dinh Chung |
| Người hướng dẫn | YAMAMOTO Shigeru |
| Cơ sở đào tạo | Trường Đại học Bách khoa, Đại học Đà Nẵng |
| Năm | 2017 |
| Nguồn | Thư viện số Trường Đại học Bách khoa, Đại học Đà Nẵng · trang gốc |
Tóm tắt
Doctoral thesis. Major: Electrical and computer engineering; 73 pages Doubly-fed induction generator (DFIG) has been used popularly in variable speed wind turbines because the DFIG wind turbine uses a small back-to-back converter to interface to the connected grid, about 30% comparing to the wind turbine’s capacity, and provides a control ability as good as a variable speed wind turbine using a generator with a full converter. The most important purpose of a variable speed wind turbine or a DFIG wind turbine, in general, is to utilize fully wind energy for electric generation. To meet this objective, several publications provided different methods. Generally, the previously proposed schemes can be listed into two groups such as wind speed-based method and wind speed sensorless one. With the first group, the wind turbine can give a good performance in tracking maximum power point but it requires a precise and instantaneous wind speed measurement; this requirement hardly achieve in practice. With methods in the second group, an anemometer does not require but the wind turbine using these methods cannot track maximum power point efficiently under varying wind conditions. In this dissertation, I proposed two methods and control laws for obtaining maximum energy output of Doubly-fed induction generator wind turbine. The first method aims to improve the conventional MPPT curve method while the second one is based on an adaptive MPPT method. Both methods do not require any information of wind data or wind sensor. Comparing to the first scheme, the second method does not require the precise parameters of the wind turbine. The maximum power point tracking (MPPT) ability of these proposed methods are theoretically proven under some certain assumptions. In particular, DFIG state-space models are derived and control techniques based on the Lyapunov function are adopted to derive the control methods corresponding to the proposed maximum power point tracking schemes. The quality of the proposed methods is verified by the numerical simulation of a 1.5-MW DFIG wind turbine with the different scenario of wind velocity. The simulation results show that the wind turbine implemented with the proposed maximum power point tracking methods and control laws can track the optimal operation point more properly comparing to the wind turbine using the conventional MPPT-curve method. The power coefficient of the wind turbine using the proposed methods can retain its maximum value promptly under a drammactical change in wind velocity while this cannot achieve in the wind turbine using the conventional MPPT-curve. Furthermore, the energy output of the DFIG wind turbine using the proposed methods is higher compared to the conventional MPPT-curve method under the same conditions.
Bản toàn văn lưu tại thư viện Trường Đại học Bách khoa, Đại học Đà Nẵng
Thông tin và tóm tắt ở trên lấy từ kho số mở của thư viện trường. Bản toàn văn do thư viện trường quản lý — có nơi cho đọc trực tuyến, có nơi cần tài khoản bạn đọc của trường.
Mở tại thư viện trường ↗
Dùng tài liệu tham khảo cho đúng
- Đọc để hiểu cách người trước đặt câu hỏi, chọn phương pháp, trình bày số liệu — rồi tự làm với dữ liệu và bối cảnh của bạn.
- Ý, số liệu, bảng biểu lấy từ tài liệu này phải trích dẫn (tác giả, năm, tên đề tài, cơ sở đào tạo).
- Đề tài trùng tên vẫn làm được nếu khác đơn vị khảo sát, thời gian hoặc cách tiếp cận — nêu rõ điểm khác trong phần mở đầu.
Đề tài cùng ngành
- Ultrathin conducting polymer transducers: Fabrication, characterization, and modeling
- Nghiên cứu, đánh giá ảnh hưởng của nguồn điện gió công suất lớn đến hệ thống điện
- Khảo sát hệ thống điện tàu cá LC-02-BNN
- Phân tích chức năng và các yếu tố ảnh hưởng đến đặc tính làm việc của Rơle số bảo vệ so lệch MBA
- Nghiên cứu động cơ HCCI: Tính toán cải tạo động cơ diesel hoạt động theo nguyên lý HCCI
- Nghiên cứu động cơ HCCI: Khảo sát động cơ Skyactiv Mazda
- Phân tích đánh giá chức năng rơle họ REX670 bảo vệ cho trạm 220 kV Đồng Nai 4
- Phân tích đánh giá độ tin cậy lưới điện tỉnh Quảng Bình và đề xuất các giải pháp nâng cao độ tin cậy
Tác giả muốn gỡ, sửa thông tin hoặc bổ sung bản toàn văn: gửi yêu cầu qua trang Liên hệ, kèm đường dẫn trang này.