Investigation into compatibility between repair material and substrate concrete using experimental and finite element methods
Luận án · Tiến sĩ · năm 2006 · đề tài tham khảo
| Loại tài liệu | Luận án |
|---|---|
| Bậc học | Tiến sĩ |
| Tác giả | Rashmi Ranjan Pattnaik |
| Cơ sở đào tạo | Đại học Quốc gia TP. Hồ Chí Minh |
| Năm | 2006 |
| Nguồn | Thư viện số Đại học Quốc gia TP. Hồ Chí Minh · trang gốc |
Tóm tắt
Due to the availability of a wide variety of repair materials in the concrete repair industry, with a wide range of physical and mechanical properties, selection of repair material for a particular repair of concrete is challenging. Previous studies and the available literature indicate that the failure of concrete repairs is mainly due to improper selection of repair material based on repair material properties, without investigating compatibility between repair material and substrate concrete. The compatibility between repair material and substrate concrete exists when the composite section of repair material and substrate concrete withstands all stresses induced by applied load under different environmental conditions without experiencing distress and deterioration over a designed period of time. In this dissertation the compatibility between eight repair materials and substrate concrete was investigated in three stages. First, individual properties of the repair materials such as setting time, flow, compressive strength, flexural strength, split tensile strength, bond strength, drying shrinkage, freeze-thaw resistance, and permeability, were determined using standard ASTM test procedures. Second, the compatibility was investigated using a composite beam of repair material and substrate concrete under third point loading. Third, the correlation of repair material properties with the compatibility was investigated to predict the durability of the concrete repair. Based on these studies, a compatibility test method is proposed to examine the compatibility between repair material and substrate concrete. In the first stage of this research, many variations in the material properties were observed among the eight repair materials. While determining the slant shear bond strength of the repair materials, it was observed that the failures of the composite cylinder specimens did not occur on the slant surface for all repair materials as selected. Those types of failure lead to different values of the bond strength for the same repair materials. Slant shear bond strength test method of ASTM C 882 is widely employed, wherein a composite cylinder prepared with repair material and substrate mortar was tested under compression. In this research the potential reasons behind the different failure patterns as observed were analyzed using experimental and finite element methods. It was observed that the bond strength of the repair materials and the mode of failures depended on the mechanical properties of repair material relative to the properties of substrate mortar. Also, the surface texture of the substrate mortar and the type of curing influenced the bond strength. Based on these findings, suggestions were made to improve the ASTM C928 specification. In the second stage of this research, composite beams of repair material and substrate concrete were prepared and tested in flexure to simulate tensile stresses in the repaired section. Tensile stresses are generally observed at the joints and in the tension areas in a concrete structure, where the tension in the concrete repair is induced by imposed loads or due to environmental conditions. In this study the flexural strength, failure patterns, and load-deflection curves of the composite beam specimens were compared with the similar results of a control beam to assess the compatibility. In addition, the influence of three curing conditions was evaluated to determine the effect on the compatibility. Compressive strength, flexural strength, split tensile strength, and drying shrinkage of the repair materials and substrate concrete were investigated to aid in the analysis of the compatibility. In this study incompatibility of repair material and substrate concrete refers to a combination of factors such as (i) flexural strength of composite beam as compared to control, (ii) failure patterns (de-bonding and edge cracking), and (iii) behavior of load-deflection curves. It was observed that signi
Bản toàn văn lưu tại thư viện Đại học Quốc gia TP. Hồ Chí Minh
Thông tin và tóm tắt ở trên lấy từ kho số mở của thư viện trường. Bản toàn văn do thư viện trường quản lý — có nơi cho đọc trực tuyến, có nơi cần tài khoản bạn đọc của trường.
Mở tại thư viện trường ↗
Dùng tài liệu tham khảo cho đúng
- Đọc để hiểu cách người trước đặt câu hỏi, chọn phương pháp, trình bày số liệu — rồi tự làm với dữ liệu và bối cảnh của bạn.
- Ý, số liệu, bảng biểu lấy từ tài liệu này phải trích dẫn (tác giả, năm, tên đề tài, cơ sở đào tạo).
- Đề tài trùng tên vẫn làm được nếu khác đơn vị khảo sát, thời gian hoặc cách tiếp cận — nêu rõ điểm khác trong phần mở đầu.
Đề tài cùng ngành
- Nghiên cứu hạ thấp độ biến động và giới hạn phát hiện vàng và Platin trong một số mẫu địa chất bằng phương pháp phân tích quang phổ nguyên tử
- Năng lượng liên kết exciton trong dây lượng tử bán dẫn dạng chữ T
- Liquefaction mitigation in silty soils using stone columns supplemented with wick drains
- Nghiên cứu thành phần hóa học và hoạt tính ức chế enzyme tyrosinase trong phân đoạn I và J của cao ethyl acetate từ thân cây Mít nài (Artocarpus rigida)
- Tìm hiểu ảnh hưởng của ánh sáng xanh lên sự tăng trưởng và chín trái cà chua bi (Solanum lycopersicum var.cerasiforme)
- Phương trình sóng Kirchhoff phi tuyến với điều kiện biên Dirichlet trong không gian Sobolev có trọng
- So sánh tốc độ tăng trưởng, tỷ lệ sống, tỷ lệ chuyển đổi giới tính (toàn đực) cá điêu hồng giữa hai phương pháp cho ăn và ngâm trong hormone 17 - Methyltestosterone tại trại giống thủy sản Bình Thạnh, tỉnh An Giang.
- Sàng lọc và tối ưu hóa điều kiện nuôi cấy chủng Streptomyces sp. có khả năng sinh transglutaminase
Tác giả muốn gỡ, sửa thông tin hoặc bổ sung bản toàn văn: gửi yêu cầu qua trang Liên hệ, kèm đường dẫn trang này.