Hydrogen oxidation at solid oxide fuel cell anodes: Mechanistic, kinetic and structural studies
Luận án · Tiến sĩ · năm 2006 · đề tài tham khảo
| Loại tài liệu | Luận án |
|---|---|
| Bậc học | Tiến sĩ |
| Tác giả | Peter George Keech |
| Cơ sở đào tạo | Đại học Quốc gia TP. Hồ Chí Minh |
| Năm | 2006 |
| Nguồn | Thư viện số Đại học Quốc gia TP. Hồ Chí Minh · trang gốc |
Tóm tắt
Solid oxide fuel cells (SOFCs) are environmentally clean, high efficiency devices that operate at >600°C. Present-day SOFCs consist of Ni-based anodes, 8% yttria stabilized zirconia (YSZ) electrolytes, and manganite-based cathodes. The large-scale commercialization of SOFCs is hindered by several factors, including anode and cathode performance. This work has focused on the kinetics and mechanism of hydrogen oxidation and water reduction at Ni-based anodes and at Pt, for comparative purposes. The electrochemical methods used to obtain this information were developed first at single phase Pt and Ni, and then applied later to all other electrode materials. Experiments were carried out using a three-electrode half-cell at 750-950°C (typically at 800°C) in 97:3 H2:H2O. Using the low-field, high-field and Allen-Hickling approximations, as well impedance spectroscopy, the exchange current density (io ), the activation energy (130 kJ/mol), and the anodic and cathodic transfer coefficients were determined. In general, the rate determining step of H2 oxidation at Ni was found to be the second electron transfer step, while water reduction is significantly slower, with the first step being the slowest. While the anodic transfer coefficient at Ni is larger than at Pt, the io values cannot be compared as the reactive areas remain unknown. Therefore, Ni point electrodes, pressed against a YSZ disc, were examined to correlate the io values with the known electrode perimeter. Unfortunately, the Ni/YSZ contact region was found to be porous, so that the true area remained unknown. Efforts to use coke deposition as a means of identifying the active anode area also proved to be unsuccessful. In order to increase anode performance, high surface area NiO and YSZ sol¬derived (SD) materials were studied. Compared to ceramic grade, micron-sized NiO and YSZ, deposited using the same methods, the SD materials are very promising, being 40 to 50 times more active. A new method to establish the NiO-YSZ electrode porosity, involving monitoring the Ni2+/3+ oxide redox response in aqueous alkaline solutions was developed. As long as the sweep rate was sufficiently slow, a good correlation between the measured redox charge and the amount of NiO in the composite electrodes was seen.
Bản toàn văn lưu tại thư viện Đại học Quốc gia TP. Hồ Chí Minh
Thông tin và tóm tắt ở trên lấy từ kho số mở của thư viện trường. Bản toàn văn do thư viện trường quản lý — có nơi cho đọc trực tuyến, có nơi cần tài khoản bạn đọc của trường.
Mở tại thư viện trường ↗
Dùng tài liệu tham khảo cho đúng
- Đọc để hiểu cách người trước đặt câu hỏi, chọn phương pháp, trình bày số liệu — rồi tự làm với dữ liệu và bối cảnh của bạn.
- Ý, số liệu, bảng biểu lấy từ tài liệu này phải trích dẫn (tác giả, năm, tên đề tài, cơ sở đào tạo).
- Đề tài trùng tên vẫn làm được nếu khác đơn vị khảo sát, thời gian hoặc cách tiếp cận — nêu rõ điểm khác trong phần mở đầu.
Đề tài cùng ngành
- Thu nhận Enzym Papain để ứng dụng vào phản ứng thủy phân Protein trong bánh dâu đậu phộng
- Sàng lọc tác dụng tăng lực và chống stress kết hợp với khảo sát hóa học một số loài Schefflera, họ Araliaceae
- Nghiên cứu tác động điều hòa lipid của chế phẩm chứa chlorogenic acid thu nhận từ hạt cà phê robusta chưa rang
- Tạo và tinh sạch kháng thể thỏ đặc hiệu FCV người cộng hợp FITC
- Thiết kế lõi IP tăng tốc mạng nơ-ron tích chập và tích hợp trên nền tảng SoC RISC-V
- Planning and learning for weakly-coupled distributed agents
- Đánh giá hoạt tính gây độc ấu trùng Toxocara canis từ cao chiết cây trâm bầu Combretum quadrangulare Kurz
- Thực hiện nghĩa vụ tài sản của vợ chồng khi ly hôn
Tác giả muốn gỡ, sửa thông tin hoặc bổ sung bản toàn văn: gửi yêu cầu qua trang Liên hệ, kèm đường dẫn trang này.