Experimental and numerical study for the automatic GMA welding process
Luận án · Tiến sĩ · năm 2008 · đề tài tham khảo
| Loại tài liệu | Luận án |
|---|---|
| Bậc học | Tiến sĩ |
| Tác giả | Đoàn Thế Thảo |
| Cơ sở đào tạo | Đại học Quốc gia TP. Hồ Chí Minh |
| Năm | 2008 |
| Nguồn | Thư viện số Đại học Quốc gia TP. Hồ Chí Minh · trang gốc |
Tóm tắt
Generally, GMA (Gas Metal Arc) welding process is currently one of the most popular welding methods. To improve the welded quality and reliability as well as to increase productivity, the selection of the optimal process parameters for the robotic GMA welding process has been required as setting welding condition to archive the desired bead geometry. For this reason, it is need to know the interrelationship between the process parameters and bead geometry as welding quality. On the other hand, the welding deformations in all stages of a welding process for achieving the required precision of welded structure must be taken into account and as a result, it is required to predict the welding distortions at the early stages of welded structure design by using a simulation. Therefore, a FEM (Finite iii Element Method) model with a suitable moving heat source, which can accurately simulate the thermal histories of GMA welding process, needs to be developed. Furthermore, the determination of trajectory planning and continuous motion of welding torch without colliding with any obstacles for robotic welding system of complex structures should be considered. It is better way to build a robotic welding system using the simulation tools in order to identify some of design and planning problems at an early stage. The sequent experiments based on full factorial design have been conducted with two levels of five process parameters to obtain bead geometry of butt and lab joint type using a GMA welding process. Four empirical models have been developed: linear, curvilinear, interaction and a proposed intelligent model. Regression analysis was employed for optimization of the coefficients of linear, curvilinear, and interaction model, while GA (Genetic Algorithm) was utilized to estimate the coefficients of intelligent model. Not only the fitting of these models were checked and compared by using variance test, but also the prediction on bead geometry using the developed models were carried out based on the additional experiments. The thermal analysis models for automatic finding parameters of a moving heat source have also been proposed. An algorithm for the combining between GA and the FEM was obtained and verified based on Goldak’s work and additional experiments for multi-pass butt and fillet welded joint with dissimilar thickness. In this algorithm, GA was effectively employed to estimate the parameters of Goldak’s double ellipsoidal model. Iv Furthermore, not only the initial kinematic simulation model with six degrees of freedom for Faraman AM1 welding robot has been developed using CATIA V5 software, but also the forward and inverse kinematic equations also be obtained by using conventional numerical methods. The output results computed from simulation model were employed to compare with calculated results from kinematic equations to validate the simulation one.
Bản toàn văn lưu tại thư viện Đại học Quốc gia TP. Hồ Chí Minh
Thông tin và tóm tắt ở trên lấy từ kho số mở của thư viện trường. Bản toàn văn do thư viện trường quản lý — có nơi cho đọc trực tuyến, có nơi cần tài khoản bạn đọc của trường.
Mở tại thư viện trường ↗
Dùng tài liệu tham khảo cho đúng
- Đọc để hiểu cách người trước đặt câu hỏi, chọn phương pháp, trình bày số liệu — rồi tự làm với dữ liệu và bối cảnh của bạn.
- Ý, số liệu, bảng biểu lấy từ tài liệu này phải trích dẫn (tác giả, năm, tên đề tài, cơ sở đào tạo).
- Đề tài trùng tên vẫn làm được nếu khác đơn vị khảo sát, thời gian hoặc cách tiếp cận — nêu rõ điểm khác trong phần mở đầu.
Đề tài cùng ngành
- Khảo sát thành phần hóa học của rễ cây đậu phộng Arachis hypogaea L. , định hướng tìm kiếm sự hiện diện của resveratrol
- Transester hóa chọn lọc đối phân hỗn hợp tiêu triền một số alcol nhị cấp xúc tác với PSL
- Biến đổi ZnO với NH4F ứng dụng trong quang xúc tác
- Engineering Novel Fluorescent Proteins
- Tangent and cotangent bundles, automorphism groups and representations of Lie groups
- Nghiên cứu độ tiêu hóa protein trong thức ăn nuôi tôm thẻ chân trắng (Litopenaeus vannamei)
- Tính giải được và các tính chất của nghiệm của một số bài toán biên phi tuyến
- Khảo sát mối liên hệ định lượng giữa độc tính và cấu trúc của các hợp chất Benzen
Tác giả muốn gỡ, sửa thông tin hoặc bổ sung bản toàn văn: gửi yêu cầu qua trang Liên hệ, kèm đường dẫn trang này.